Table of Contents
How do I reset my Cisco ASA password?
To recover passwords, perform the following steps:
- Console into the ASA.
- Reboot the ASA.
- Press the escape key during reboot to enter ROMMON.
- Tell the firewall to ignore the startup config on next reload: rommon #1> confreg.
How do I reset my ASA 5505?
- After you open connection, press enter a couple of times, and you should get a prompt like: ‘ciscoasa>’
- type ‘enable’ to go to enable mode.
- type ‘config t’
- type ‘config factory-default’
- hit spacebar when the ‘more’ is displayed.
- type ‘reload save-config noconfirm’
What is the default password for Cisco ASA 5505?
IP Address | |
---|---|
Username | Cisco |
Password | Cisco |
SSID |
What is the default enable password on a Cisco ASA?
Connect your console cable to the ASA and connect to it via Putty. Once the ASA has finished loading, go into enable mode. The default password is cisco with no username.
How do I log into Cisco ASA?
ASDM Web Access Guide:
- On the PC connected to the ASA, launch a web browser. (Verify that Java and JavaScript are enabled in your web browser)
- In the Address field, enter the following (default) URL: https://192.168.1.1/admin.
- Run Startup Wizard.
How do I find my Cisco ASA encrypted password?
Normally, you use the ‘show run’ command to view the running configuration. Pre-shared keys are marked with an asterisk (*). To view the password unencrypted, type ‘more system:running-config’. This will display the full configuration with unencrypted passwords.
What is Cisco default password?
admin
Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168.
How do I connect to a Cisco ASA 5505 console?
Step 1 Plug one end of the PC terminal adapter into a standard 9-pin PC serial port on your PC. Step 2 Plug one end of the blue console cable into the PC terminal adapter. Step 3 Plug the other end of the blue console cable into the Console port.
How do I connect to a Cisco ASA 5505?
Cisco ASA 5505 configuration
- Step1: Configure the internal interface vlan.
- Step 2: Configure the external interface vlan (connected to Internet)
- Step 3: Assign Ethernet 0/0 to Vlan 2.
- Step 4: Enable the rest interfaces with no shut.
- Step 5: Configure PAT on the outside interface.
- Step 6: Configure default route.
How do I log into my Cisco ASA 5505?
Initial setup and configuration of interfaces
- Connect the network cable from the modem to port 0 (default outside port) on the ASA.
- Connect your computer to one of the other ports on the ASA, which should be on the inside network by default.
- Open a browser on your computer and go to 192.168.
- Click Run ASDM.
- Log in.
How do I connect to ASA 5505?
How do you reset your Cisco password?
Press the Menu Button. Press the Up or Down scroll button to select the Admin Setup menu. Press the Select button. Enter the administrator password (the default admin password is **#) and press the Enter softkey. Press the Down scroll button to select Restore Defaults. Press the Select button.
What is the default password for Cisco?
Cisco Default Password List. Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168.1.1 or 192.168.1.254. However, some differ as shown in the table below. Important: Remember to change the default login data once you’re in! See below the table for more help,…
What is the password for Cisco routers?
Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168.1.1 or 192.168.1.254.