Table of Contents
What is rework station used for?
A hot air gun or hot air station is used to heat devices and melt solder, and specialised tools are used to pick up and position often tiny components. A rework station is a place to do this work—the tools and supplies for this work, typically on a workbench.
Can you solder with a rework station?
Those who occasionally repair electronic gadgets, they know the importance of using hot air rework stations. They assist you to safely solder as well as de-solder parts in less time and with great accuracy. Moreover, they are perfect for attaching and detaching SMD components like PLCCs, BGAs, ICs, and SOICs.
Can you solder with hot air gun?
A common heat gun is an inexpensive way to reflow, or reattach, electronic components that have been soldered together. Before you begin soldering, make sure that all the small components on your board are held down; the heat gun produces a lot of air that can blow these parts away.
How do you use a hot air gun for desoldering?
How to use a desoldering gun. Prepare the desoldering gun by plugging it in, turning it on, and setting the desired temperature. Wait for the nozzle to get up to temperature, and then apply solder to it. The solder helps form a heat bridge between the nozzle and the solder on the circuit board that needs to be molten.
What is the difference between a hot air gun and a heat gun?
Heat guns, often called hot air guns or hot air stations for this application, are used in electronics to desolder and rework surface-mounted circuit board components. Heat guns are also used for functional testing of overheat protection devices, in order to safely simulate an overheat condition.
How hot does a hot air gun get?
The top temperature of a heat gun typically reaches around 1,100 degrees Fahrenheit (593 degrees Celsius), although some get even hotter. For most heat gun uses, 750 degrees Fahrenheit (399 degrees Celsius) will suffice [source: Capotosto].
What do you use a hot air gun for?
Hot air guns, or heat guns, extend a jet of air that can be directed to a specific point or surface. They can reach very high temperatures and are used, among other things, to strip paint, shrink hose, defrost pipes, melt metal and plastic or weld different materials together.
How do you reflow a GPU?
Apply thermal paste onto the main chip or on the connection side of the fan. Place the heat-sink over the GPU carefully, lining up any screws or clips. Apply heatsink on thermal pads as applicable. Use only a small amount of heatsink and spread evenly using a card, or apply pressure evenly when connecting components.
Is flux necessary for desoldering?
Flux’s job is to clean copper by removing impurities so that solder can properly wet (think “adhere”). When desoldering, you should apply flux to whatever the solder is supposed to wet to. If you are using a copper desoldering braid, then apply a bit of flux to it.
What is the size of the rework station?
The rework station fits boards up to 16.5 inches and has the capability to place components from 4 millimeters to 55 millimeters. A great entry level BGA Rework Station for jobs that don’t require split vision assist camera.
What is the best rework station for circuit board repair?
The SP-360C BGA Rework Station is a basic rework station that is ideal for entry-level circuit board repair jobs. This rework station does not have a split-vision assist camera. The rework station fits boards up to 16.5 inches and has the capability to place components from 4 millimeters to 55 millimeters.
How does a hot air rework station work?
Hot air rework stations will typically employ focused heated air on the top and an unfocused board heater for the lower portion of the heating area. The flow of air will heat over the BGA and under the board as well. The bottom part of the heating compartment will consist of either a plate heater or an infrared light heater.
How does a BGA rework station work?
In cases where the ball grid array (BGA) needs to be repaired, the board will usually need to be heated to remove faulty parts and replace them with new ones. These steps are performed in a BGA rework station, which is a device designed and equipped for heating printed circuit boards to remove and replace malfunctioning parts.