Table of Contents
- 1 What type of fuse does a subwoofer use?
- 2 How do I know what size fuse for my amp?
- 3 What size fuse should I use for a 1200 watt amp?
- 4 How many watts can a 30 amp fuse handle?
- 5 What size speaker wire do I need to wire a subwoofer?
- 6 Why do I need a fuse for a 150 watt bulb?
- 7 What amperage rating do I need to fuse a motmotor?
What type of fuse does a subwoofer use?
Top Reasons Why Subwoofer Fuses Blow Out There are two types of fuses that could be used. One type is the slow blow fuse, which will enable the device to withstand an over-current condition over a very short period, and the second is a fast acting fuse, which would blow more quickly in an over-currant situation.
How do I know what size fuse for my amp?
The correct size of fuse to use depends on the amp you are wiring. If your amp has an internal fuse, then your inline car amp fuse should be a bit larger. For instance, if your amp has an internal 20 amp fuse, then you should go for a 25 or 30 amp inline fuse.
Why does my subwoofer keep blowing fuses?
In most cases, an amplifier will blow fuses due to internal damage caused by the way it was installed. An amplifier that blows the main power fuse immediately after you turn it on or when the fuse is inserted into the fuse holder is usually damaged in its power supply or output section, and will require serviced.
What size fuse should I use for a 1200 watt amp?
You should use at least a 100A fuse.
How many watts can a 30 amp fuse handle?
3,600 watts
A 30-amp outlet supplies 3,600 watts (30 amps multiplied by 120 volts). Therefore, the breaker on that outlet could meet code and still trip anywhere between a total load of 2,880 watts (80 percent of 3,600 watts) and 4,320 watts (120 percent of 3,600 watts).
What size is an AGU Fuse?
AGU Fuses: The largest fuse in this image is the glass AGU fuse which measures 11/2″ X 13/32″. These fuses are available in current ratings between 10 and 80 amps. AGU fuses can be used to protect the main power wire of small to moderately high power systems….
| Wire Gauge | Recommended Maximum Fuse Size |
|---|---|
| 16 awg | 7.5 amps |
What size speaker wire do I need to wire a subwoofer?
All the wires depicted in the Subwoofer Wiring Diagrams are speaker wires. For wiring subwoofers, we recommend using wires of 12- to 16-gauge in size. [Shop for speaker wire] Start building your bass system today
Why do I need a fuse for a 150 watt bulb?
You install a fuse to PROTECT the WIRE!!!!!! That means FIRST you determine what size WIRE you need based on the Length of the wire run to the 150 watt lights. If there is some pre installed factory wire and you have changed the lights. The FUSE size for that Factory wire has already been determined and should NOT be increased!
What size fuse do I need for my wires?
For your fuse to do its job correctly and protect your wires, it should be rated about 1.1 to 1.5 times the rated current value. It’s also a great idea to get an ATC fuse holder to protect and mount your fuse. One common misconception about choosing the correct fuse size is that it’s dependent on the load of the circuit.
What amperage rating do I need to fuse a motmotor?
Motors should be fused with a time-delay fuse rated 175\% of the motor’s full load operating amperage, 250\% of the full load operating amperage if a circuit breaker is used. The wire to a motor must be rated to carry 25\% more amperage than the motor draws when operating at full load. This amperage rating is listed on most motors.